How does electrical safety system work on ISS?Plumbing work of ISS?How would a centrifuge module's berthing system work on the ISS?Does GPS work at ISS?Where does electrical power on a rocket come from?Could the space shuttle be permanently left in orbit as a space station?How exactly does the live feed from ISS work?If electronics are magnetic, how do they work in space?How does SpaceX Falcon Heavy Starman live feed transmitter work?How does the sabatier system reduce water shipments to the ISS?How does this ISS vision-testing instrument work? What exactly is being measured, and how?

Transformation of random variables and joint distributions

Could solar power be utilized and substitute coal in the 19th century?

Why has "pence" been used in this sentence, not "pences"?

Do the concepts of IP address and network interface not belong to the same layer?

Flux received by a negative charge

Proof of Lemma: Every nonzero integer can be written as a product of primes

What linear sensor for a keyboard?

Is it possible to have a strip of cold climate in the middle of a planet?

How do I implement a file system driver driver in Linux?

Is possible to search in vim history?

Visiting the UK as unmarried couple

Diode in opposite direction?

Drawing ramified coverings with tikz

Why is Arduino resetting while driving motors?

Why in book's example is used 言葉(ことば) instead of 言語(げんご)?

What (else) happened July 1st 1858 in London?

Can somebody explain Brexit in a few child-proof sentences?

Confusion on Parallelogram

How do I extrude a face to a single vertex

Why does the integral domain "being trapped between a finite field extension" implies that it is a field?

Drawing a topological "handle" with Tikz

Using a siddur to Daven from in a seforim store

If a character with the Alert feat rolls a crit fail on their Perception check, are they surprised?

Is there a conventional notation or name for the slip angle?



How does electrical safety system work on ISS?


Plumbing work of ISS?How would a centrifuge module's berthing system work on the ISS?Does GPS work at ISS?Where does electrical power on a rocket come from?Could the space shuttle be permanently left in orbit as a space station?How exactly does the live feed from ISS work?If electronics are magnetic, how do they work in space?How does SpaceX Falcon Heavy Starman live feed transmitter work?How does the sabatier system reduce water shipments to the ISS?How does this ISS vision-testing instrument work? What exactly is being measured, and how?













13












$begingroup$


Is there any possibility that the power consumption is greater than power supply on ISS? What happens (or potentially would happen) if we plug too many electric devices so that ISS couldn't handle it?



I believe that there is an emergency system which powers life control system when fuses are blown. Would astronauts then have to replace the fuses? If yes, how much time do they have for that?










share|improve this question









$endgroup$







  • 2




    $begingroup$
    Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
    $endgroup$
    – Carl Witthoft
    Mar 21 at 15:49










  • $begingroup$
    @CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
    $endgroup$
    – Elgirhath
    Mar 21 at 18:29







  • 1




    $begingroup$
    @CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
    $endgroup$
    – Martin Bonner
    Mar 21 at 18:30















13












$begingroup$


Is there any possibility that the power consumption is greater than power supply on ISS? What happens (or potentially would happen) if we plug too many electric devices so that ISS couldn't handle it?



I believe that there is an emergency system which powers life control system when fuses are blown. Would astronauts then have to replace the fuses? If yes, how much time do they have for that?










share|improve this question









$endgroup$







  • 2




    $begingroup$
    Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
    $endgroup$
    – Carl Witthoft
    Mar 21 at 15:49










  • $begingroup$
    @CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
    $endgroup$
    – Elgirhath
    Mar 21 at 18:29







  • 1




    $begingroup$
    @CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
    $endgroup$
    – Martin Bonner
    Mar 21 at 18:30













13












13








13


1



$begingroup$


Is there any possibility that the power consumption is greater than power supply on ISS? What happens (or potentially would happen) if we plug too many electric devices so that ISS couldn't handle it?



I believe that there is an emergency system which powers life control system when fuses are blown. Would astronauts then have to replace the fuses? If yes, how much time do they have for that?










share|improve this question









$endgroup$




Is there any possibility that the power consumption is greater than power supply on ISS? What happens (or potentially would happen) if we plug too many electric devices so that ISS couldn't handle it?



I believe that there is an emergency system which powers life control system when fuses are blown. Would astronauts then have to replace the fuses? If yes, how much time do they have for that?







iss power electronics






share|improve this question













share|improve this question











share|improve this question




share|improve this question










asked Mar 21 at 11:59









ElgirhathElgirhath

785




785







  • 2




    $begingroup$
    Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
    $endgroup$
    – Carl Witthoft
    Mar 21 at 15:49










  • $begingroup$
    @CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
    $endgroup$
    – Elgirhath
    Mar 21 at 18:29







  • 1




    $begingroup$
    @CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
    $endgroup$
    – Martin Bonner
    Mar 21 at 18:30












  • 2




    $begingroup$
    Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
    $endgroup$
    – Carl Witthoft
    Mar 21 at 15:49










  • $begingroup$
    @CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
    $endgroup$
    – Elgirhath
    Mar 21 at 18:29







  • 1




    $begingroup$
    @CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
    $endgroup$
    – Martin Bonner
    Mar 21 at 18:30







2




2




$begingroup$
Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
$endgroup$
– Carl Witthoft
Mar 21 at 15:49




$begingroup$
Just wondering what country you are residing in -- many countries have switched over almost entirely to resettable breakers rather than fuses for commercial and residential buildings.
$endgroup$
– Carl Witthoft
Mar 21 at 15:49












$begingroup$
@CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
$endgroup$
– Elgirhath
Mar 21 at 18:29





$begingroup$
@CarlWitthoft I'm from Poland, and now I'm quite convinced that this happened here too, but I was probably influenced by my experience with car fuses ;)
$endgroup$
– Elgirhath
Mar 21 at 18:29





1




1




$begingroup$
@CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
$endgroup$
– Martin Bonner
Mar 21 at 18:30




$begingroup$
@CarlWitthoft One of those countries is the UK - but I still refer to "fuses" and "the fusebox".
$endgroup$
– Martin Bonner
Mar 21 at 18:30










1 Answer
1






active

oldest

votes


















22












$begingroup$

This answer addresses only the US side of the ISS.



Like everything else on the ISS, it's complicated.



enter image description here



Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



enter image description here




I believe that there is an emergency system which powers life control system when fuses are blown.




As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



Acronymology:



  • ARCU - American / Russian Conversion Unit

  • BCDU - Battery Charge / Discharge Unit


  • BGA - Beta Gimbal Assembly


  • DDCU - DC / DC Converter Unit

  • ECU - Electrical Control Unit

  • IDA - Integrated Distribution Assembly

  • IEA - Integrated Electronics Assembly

  • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
    onboard computer)

  • PFCS - Pump / Flow Control System

  • PVA - Photovoltaic Array

  • PVR - Photovoltaic Radiator

  • RPDA - Remote Power Distribution Assembly

  • SPDA - Secondary Power Distribution Assembly

  • SSU - Sequential Shunt Unit

  • Z1 - the name of a centrally located ISS truss unit

Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.






share|improve this answer











$endgroup$












    Your Answer





    StackExchange.ifUsing("editor", function ()
    return StackExchange.using("mathjaxEditing", function ()
    StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
    StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["$", "$"], ["\\(","\\)"]]);
    );
    );
    , "mathjax-editing");

    StackExchange.ready(function()
    var channelOptions =
    tags: "".split(" "),
    id: "508"
    ;
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function()
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled)
    StackExchange.using("snippets", function()
    createEditor();
    );

    else
    createEditor();

    );

    function createEditor()
    StackExchange.prepareEditor(
    heartbeatType: 'answer',
    autoActivateHeartbeat: false,
    convertImagesToLinks: false,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: null,
    bindNavPrevention: true,
    postfix: "",
    imageUploader:
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    ,
    noCode: true, onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    );



    );













    draft saved

    draft discarded


















    StackExchange.ready(
    function ()
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fspace.stackexchange.com%2fquestions%2f34966%2fhow-does-electrical-safety-system-work-on-iss%23new-answer', 'question_page');

    );

    Post as a guest















    Required, but never shown

























    1 Answer
    1






    active

    oldest

    votes








    1 Answer
    1






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes









    22












    $begingroup$

    This answer addresses only the US side of the ISS.



    Like everything else on the ISS, it's complicated.



    enter image description here



    Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



    The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



    If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



    If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



    enter image description here




    I believe that there is an emergency system which powers life control system when fuses are blown.




    As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



    Acronymology:



    • ARCU - American / Russian Conversion Unit

    • BCDU - Battery Charge / Discharge Unit


    • BGA - Beta Gimbal Assembly


    • DDCU - DC / DC Converter Unit

    • ECU - Electrical Control Unit

    • IDA - Integrated Distribution Assembly

    • IEA - Integrated Electronics Assembly

    • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
      onboard computer)

    • PFCS - Pump / Flow Control System

    • PVA - Photovoltaic Array

    • PVR - Photovoltaic Radiator

    • RPDA - Remote Power Distribution Assembly

    • SPDA - Secondary Power Distribution Assembly

    • SSU - Sequential Shunt Unit

    • Z1 - the name of a centrally located ISS truss unit

    Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.






    share|improve this answer











    $endgroup$

















      22












      $begingroup$

      This answer addresses only the US side of the ISS.



      Like everything else on the ISS, it's complicated.



      enter image description here



      Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



      The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



      If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



      If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



      enter image description here




      I believe that there is an emergency system which powers life control system when fuses are blown.




      As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



      Acronymology:



      • ARCU - American / Russian Conversion Unit

      • BCDU - Battery Charge / Discharge Unit


      • BGA - Beta Gimbal Assembly


      • DDCU - DC / DC Converter Unit

      • ECU - Electrical Control Unit

      • IDA - Integrated Distribution Assembly

      • IEA - Integrated Electronics Assembly

      • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
        onboard computer)

      • PFCS - Pump / Flow Control System

      • PVA - Photovoltaic Array

      • PVR - Photovoltaic Radiator

      • RPDA - Remote Power Distribution Assembly

      • SPDA - Secondary Power Distribution Assembly

      • SSU - Sequential Shunt Unit

      • Z1 - the name of a centrally located ISS truss unit

      Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.






      share|improve this answer











      $endgroup$















        22












        22








        22





        $begingroup$

        This answer addresses only the US side of the ISS.



        Like everything else on the ISS, it's complicated.



        enter image description here



        Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



        The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



        If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



        If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



        enter image description here




        I believe that there is an emergency system which powers life control system when fuses are blown.




        As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



        Acronymology:



        • ARCU - American / Russian Conversion Unit

        • BCDU - Battery Charge / Discharge Unit


        • BGA - Beta Gimbal Assembly


        • DDCU - DC / DC Converter Unit

        • ECU - Electrical Control Unit

        • IDA - Integrated Distribution Assembly

        • IEA - Integrated Electronics Assembly

        • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
          onboard computer)

        • PFCS - Pump / Flow Control System

        • PVA - Photovoltaic Array

        • PVR - Photovoltaic Radiator

        • RPDA - Remote Power Distribution Assembly

        • SPDA - Secondary Power Distribution Assembly

        • SSU - Sequential Shunt Unit

        • Z1 - the name of a centrally located ISS truss unit

        Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.






        share|improve this answer











        $endgroup$



        This answer addresses only the US side of the ISS.



        Like everything else on the ISS, it's complicated.



        enter image description here



        Fuses are not commonly used on the ISS. There are fuses within the battery subassemblies, to protect against internal battery shorts.



        The common circuit protection device on the ISS is the Remote Power Controller (RPC), a commandable "smart circuit breaker". An RPC monitors the current passing through it and opens the circuit if the current exceeds a limit for a specified amount of time. The RPC can be commanded to reset once the problem has been resolved. The RPCs are grouped into RPC Modules (RPCMs). If the input voltage to an RPCM drops too low, all the RPCs in the RPCM will open.



        If the power usage gets higher than the supplied power can handle (for example, if a solar array is lost), the onboard computers (MDMs) can command a 'load shed'. Using tables preloaded into the software, the MDM(s) controlling the electrical power system will command the RPCs on a set of devices open, powering them off.



        If the power loss event is predicted, the flight controllers can most likely do a better job of powering down the station based on the current configuration than the load shed tables would. They would send commands to open the desired RPCs.



        enter image description here




        I believe that there is an emergency system which powers life control system when fuses are blown.




        As stated, fuses are not commonly used, and there is no such emergency system. The ISS already runs off battery power when the solar arrays are not generating power. The load shed tables are built so that critical functions are the last to be turned off.



        Acronymology:



        • ARCU - American / Russian Conversion Unit

        • BCDU - Battery Charge / Discharge Unit


        • BGA - Beta Gimbal Assembly


        • DDCU - DC / DC Converter Unit

        • ECU - Electrical Control Unit

        • IDA - Integrated Distribution Assembly

        • IEA - Integrated Electronics Assembly

        • MDM - Multiplexer / Demultiplexer (an absolutely awful name for an
          onboard computer)

        • PFCS - Pump / Flow Control System

        • PVA - Photovoltaic Array

        • PVR - Photovoltaic Radiator

        • RPDA - Remote Power Distribution Assembly

        • SPDA - Secondary Power Distribution Assembly

        • SSU - Sequential Shunt Unit

        • Z1 - the name of a centrally located ISS truss unit

        Source - personal notes. NASA does not provide a good reference source for the ISS. There is some information in this paper, from which the images are taken.







        share|improve this answer














        share|improve this answer



        share|improve this answer








        edited Mar 21 at 20:58

























        answered Mar 21 at 13:14









        Organic MarbleOrganic Marble

        59.4k3164255




        59.4k3164255



























            draft saved

            draft discarded
















































            Thanks for contributing an answer to Space Exploration Stack Exchange!


            • Please be sure to answer the question. Provide details and share your research!

            But avoid


            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.

            Use MathJax to format equations. MathJax reference.


            To learn more, see our tips on writing great answers.




            draft saved


            draft discarded














            StackExchange.ready(
            function ()
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fspace.stackexchange.com%2fquestions%2f34966%2fhow-does-electrical-safety-system-work-on-iss%23new-answer', 'question_page');

            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown







            Popular posts from this blog

            Kamusi Yaliyomo Aina za kamusi | Muundo wa kamusi | Faida za kamusi | Dhima ya picha katika kamusi | Marejeo | Tazama pia | Viungo vya nje | UrambazajiKuhusu kamusiGo-SwahiliWiki-KamusiKamusi ya Kiswahili na Kiingerezakuihariri na kuongeza habari

            SQL error code 1064 with creating Laravel foreign keysForeign key constraints: When to use ON UPDATE and ON DELETEDropping column with foreign key Laravel error: General error: 1025 Error on renameLaravel SQL Can't create tableLaravel Migration foreign key errorLaravel php artisan migrate:refresh giving a syntax errorSQLSTATE[42S01]: Base table or view already exists or Base table or view already exists: 1050 Tableerror in migrating laravel file to xampp serverSyntax error or access violation: 1064:syntax to use near 'unsigned not null, modelName varchar(191) not null, title varchar(191) not nLaravel cannot create new table field in mysqlLaravel 5.7:Last migration creates table but is not registered in the migration table

            은진 송씨 목차 역사 본관 분파 인물 조선 왕실과의 인척 관계 집성촌 항렬자 인구 같이 보기 각주 둘러보기 메뉴은진 송씨세종실록 149권, 지리지 충청도 공주목 은진현